Media Summary: Microwire 93C86 and 24LC04 EEPROM from Samsung Toner. Software version 1.30 added a command "fdisk". This is an example of the output Device Start Size Id Type 1.img 2a0000 300000 ... This is TQ2440, a S3C2440 dev board. It has both NAND and Nor flash. My earlier video shows how to

U Link Nt Program Ds2431 - Detailed Analysis & Overview

Microwire 93C86 and 24LC04 EEPROM from Samsung Toner. Software version 1.30 added a command "fdisk". This is an example of the output Device Start Size Id Type 1.img 2a0000 300000 ... This is TQ2440, a S3C2440 dev board. It has both NAND and Nor flash. My earlier video shows how to 24M02 is a 256KB EEPROM with page size of 256 bytes. 5P08 uses SPI protocol. Both are now supported in 1.46. If your chip is ... JTAG pin finder. Try to avoid reset pin to be connected since it will not detect the pins properly. Make connection, power on the ... Then there is a easiest way to make connection to

Mistake 1. Not making good contact. Mistake 2. Wiggle the clip while power is on. (Need to remove power and USB to adjust clip).

Photo Gallery

u-Link NT program DS2431(1 wire)
u-Link NT program EEPROM.
u-Link NT 1.30 program Birware and Alphaware on SB6190
u-Link NT introduction.
u-Link NT Program Nand flash on S3C2440 via JTAG port.
u-Link NT Program SD card (Prototype)
u-Link NT program 24M02 and 5P08 EEPROM
u-link NT and USB BDM NT program DCT2224 (MC68332)
u-Link NT Program ST20 (ExtreamView3300)
u-Link NT to scan JTAG pinout.
Easiest 16 pin SPI connection with u-Link NT. (No soldering)
Common mistakes for SPI flash programming on board using u-Link NT (USB JTAG NT).
View Detailed Profile
u-Link NT program DS2431(1 wire)

u-Link NT program DS2431(1 wire)

Software 1.10. EEPROM

u-Link NT program EEPROM.

u-Link NT program EEPROM.

Microwire 93C86 and 24LC04 EEPROM from Samsung Toner.

u-Link NT 1.30 program Birware and Alphaware on SB6190

u-Link NT 1.30 program Birware and Alphaware on SB6190

Software version 1.30 added a command "fdisk". This is an example of the output Device Start Size Id Type 1.img 2a0000 300000 ...

u-Link NT introduction.

u-Link NT introduction.

Introducing

u-Link NT Program Nand flash on S3C2440 via JTAG port.

u-Link NT Program Nand flash on S3C2440 via JTAG port.

This is TQ2440, a S3C2440 dev board. It has both NAND and Nor flash. My earlier video shows how to

u-Link NT Program SD card (Prototype)

u-Link NT Program SD card (Prototype)

The plan is to use

u-Link NT program 24M02 and 5P08 EEPROM

u-Link NT program 24M02 and 5P08 EEPROM

24M02 is a 256KB EEPROM with page size of 256 bytes. 5P08 uses SPI protocol. Both are now supported in 1.46. If your chip is ...

u-link NT and USB BDM NT program DCT2224 (MC68332)

u-link NT and USB BDM NT program DCT2224 (MC68332)

u

u-Link NT Program ST20 (ExtreamView3300)

u-Link NT Program ST20 (ExtreamView3300)

The read speed is very fast. The

u-Link NT to scan JTAG pinout.

u-Link NT to scan JTAG pinout.

JTAG pin finder. Try to avoid reset pin to be connected since it will not detect the pins properly. Make connection, power on the ...

Easiest 16 pin SPI connection with u-Link NT. (No soldering)

Easiest 16 pin SPI connection with u-Link NT. (No soldering)

Then there is a easiest way to make connection to

Common mistakes for SPI flash programming on board using u-Link NT (USB JTAG NT).

Common mistakes for SPI flash programming on board using u-Link NT (USB JTAG NT).

Mistake 1. Not making good contact. Mistake 2. Wiggle the clip while power is on. (Need to remove power and USB to adjust clip).

u-Link NT program Atmega chip

u-Link NT program Atmega chip

u